Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kakehi, Isao;
JNC TN9400 2000-054, 84 Pages, 2000/04
JNC-TN9400-2000-054.pdf:7.15MB
This report describes accomplishment of the study on the quality of vipac (vibro-packed) oxide fuel obtained by pyrochemical processing (molten salt electrolytic processing). This study is intended to contribute to the design study of the pyro-reprocessing-vipac fuel recycling system of oxide fuel. In this study, vibro-packing experiment has been conducted using granular U0
obtained by molten salt electrolytic processing (cold experiment). The oxide pyro process developed by Research lnstitute of Atomic Reactors (RIAR) is the method in which the sintered oxide is electrically deposited on the cathode at approximately 600
C. 0xide granules for vipac fuel are obtained by crushing the oxide deposited on the cathode. This process is also developed as recycle process because it is capable of FP separation. Also in Japan, this process is studied as one of the new FBR fuel recycling systems. ln this study, we made an effort to clarify the mechanisms of vibro-packing of the electrically obtained granules, which influence on the effective parameters of vibro-packing density and fuel particles size distribution in the fuel cladding in case of non-sphere particles of the granules. As a result of the study, smear density of 75% and almost uniform distribution of U0 particles have been taken in the experiment, and much knowledge for the improvement of the vibro-packing quality has been found. And the possibility of the smear density over 80% and the uniform distribution of U0 particles has been suggested in this study.
Tozawa, Katsuhiro; ; Kakehi, Isao
JNC TN9400 2000-052, 110 Pages, 2000/04
JNC-TN9400-2000-052.pdf:4.39MB
This report describes accomplishment of development of a cathode processor calculation code to simulate the mass and heat transfer phenomena with the distillation process and development of an analytical model for cooling behavior of the pyrochemical process cell on personal computers. The pyrochemical process using molten salt electrorefining would introduce new technologies for new fuels of particle oxide, particle nitride and metallic fuels. The cathode processor calculation code with distillation process was developed. A code validation calculation has been conducted on the basis of the benchmark problem for natural convection in a square cavity. Results by using the present code agreed well for the velocity-temperature fields, the maximum velocity and its location with the benchmark solution published in a paper. The functions have been added to advance the reality in simulation and to increase the efficiency in utilization. The test run has been conducted using the code with the above modification for an axisymmetric enclosed vessel simulating a cathode processor, and the capability of the distillation process simulation with the code has been confirmed. An analytical model for cooling behavior of the pyrochemical process cell was developed. The analytical model was selected by comparing benchmark analysis with detailed analysis on engineering workstation. Flow and temperature distributions were confirmed by the result of steady state analysis. In the result of transient cooling analysis, an initial transient peak of temperature occurred at balanced heat condition in the steady-state analysis. Final gas temperature distribution was dependent on gas circulation flow in transient condition. Then there were different final gas temperature distributions on the basis of the result of steady-state analysis. This phenomenon has a potential for it's own metastable condition. Therefore it was necessary to design gas cooling flow pattern without ...
Kakehi, Isao; Nakabayashi, Hiroki
JNC TN9400 2000-051, 237 Pages, 2000/04
JNC-TN9400-2000-051.pdf:8.14MB
In this study, we have proposed the concept of safety systems (solutions of safety problems) in pyrochemical reprocessing systems (lt consists of pyrochemical reprocessing methods and the injection casting process for the metal fuel fabrication, or vibro-packing process for the oxide fuel fabrication.) which has different concept from the existing PUREX reprocessing method and pellet fuel fabrication process. And we performed its safety evaluations. FoIlowing the present Japanese safety regulations for reprocessing facilities, we pointed out functions, design requirements and equipments relating to its safety systems and picked up subjects. For the survey of safety evaluations, we first selected anticipated events and accident events, and second by evaluated 6the correspondence of the limitation of the public exposure to the accidents above, by using two parameters, the safety design parameter (the filter performance to confine radioactive matelials) and the leak inventory of radioactivities, and last by picked up its problems. ln addition to the above evaluations we performed basic criticality analyses for its systems to utilize these results for the design and evaluation of the criticality safety management system. Thus this study specified the concept of safety systems for pyrochemical reprocessing processes and then issues in order to establish safety design policies (matters which must consider for the safety design) and guides and to advance more definite safety design.